“scooters batteries -bike batteries”

The controller that came with my ebike conversion kit just has the label ’48v 1000w’ on it and there are no other specifications anywhere to be seen. I have emailed the suppliers asking if I could have a full list of specifications for the controller but am yet to hear back from them.

A big downside of lithium batteries is that they are much more expensive than lead acid batteries. Prices vary depending on the voltage and capacity of the lithium battery, but standard ebikes usually have lithium batteries starting in the $300 range and rising quickly from there. Most bikes I build have lithium batteries in the $400-$500 range.

BMS’s aren’t required, they just make life easier. As you mentioned, if you don’t use a BMS then you’ve got to diligently monitor your cells and use balance charging to manually balance your cells. A BMS just takes care of this hassle for you. A low quality BMS can cause problems, but good quality BMS’s shouldn’t risk cell damage.

This is 14 series 52V (58.8v full charge) lithium battery power protection board. Balanced, same port continuous 45A discharge. 1x 14S 45A Lithium Battery Protection Board. Step2:After confirm the wir…

Your method of using the tubes might work but I still worry about how much current you could safely pull out of those connections. You can definitely charge the way you described but trust me, charging 2 or 4 cells at a time gets VERY frustrating. You’ll be spending days, maybe a week, getting your battery all the way charged again.

There is a recently introduced battery chemistry that we will likely be seeing a lot of soon. Lithium-Nickel-Manganese-Cobalt-Oxide, or LiNiMnCoO2/NMC. Since Asian battery manufacturers have been working on a wide variety of alternative chemistries, a manufacturer standards group has chosen the  abbreviation NMC for this chemistry (although one wholesaler stubbornly calls it NCM).

3. Lastly, I assume if the BMS & battery were able to produce the 50A X 24V watts of 1200W that my electric motor would only ever use the 500W it is rated for? As in the E bikes controller would only draw around 500W?

Yes, I’ve seen this problem. Homes that have only a 10A circuit breaker are often not enough for these welders. The room I wanted to use mine in had a 10A, so I switched it for a 20A breaker at the breaker box and now it works fine.

Well, we here at electricbike.com are glad you asked! http://twowheelev.com of this month (Feb 2013), nobody is selling completed packs with the new NCA chemistry to the public, but the cylindrical cell that will be up to bat next is…

NiCd-Nickel Cadmium. This chemistry was half the size per a given power compared to SLA. But it has a low C-rate (Current producing capability) so anyone who made a pack out of them was restricted to low amps. There were no large packs for sale. E-bikers had to purchase rechargeable flashlight batteries and solder together a pack of a higher voltage, for which an off-the-shelf charger could be found to charge it up. Because of the low price of SLA chargers, 36V and 48V NiCd systems were common. When the price of nickel went up and the price of Lithium came down, NiCd died a quick death. Not even cordless drills use these anymore.

What does that mean?. Well, it is like having another fit bicycle rider helping you pedal, but without their weight. No matter how hard your hills, or heavy your bike is, this motor will always work t…

There are six rechargeable battery types that have seen regular use in electric bicycle battery packs. We have never been involved with lead acid batteries, and discontinued dealing NiCad and NiMH packs in 2010.

The Powerful 350W Brusless Motor Has Excellent Power To Reach Speeds Up To 12.5MPH And On Hills It Gives You The Power To Easily Reach The Top. Power: 350W. Turning e-Bike riders into explorers and ad…

The 48V, 8AH lithium battery of this ebike is removable. Material: Aluminium alloy frame. E-bike & Assisted bicycle, you can choose the E-bike to enjoy a long time travel, and also exercise. Combining…

I have found this BMS which is cheap (necessary for my project) and it is shipped from the UK. Because it is so cheap do you think that it may not be balancing? http://www.ebay.co.uk/itm/400984825723?euid=0502c7e2b2c744ec8857879d65d46e08&cp=1

Also changing the fuse to a higher one could cause the wires to start a fire and the whole house would burn down if the wires are not thick enough. Also in sweden a fuse gets bigger as they are rated higher so you can fit a 20A fuse in a 10A slot, for safety.

I’m wondering, what do you do for 6V or 12V applications where the correct number of in-series cells is ambiguous? For example, if I’m replacing a 6V SLA battery, it seems like the existing charging system would set a 1s battery on fire, but wouldn’t be sufficient to charge a 2s battery. Are there BMS’s that have VRs to step up the voltage from the charging system to the battery, and step down voltage from the battery to the charging system to facilitate a 2s battery for the application?

Lipo batteries are currently the “hottest” battery choice for electric bike enthusiasts. LiPo batteries are the most power-dense type of  battery available to electric bike riders today. The problem is that LiPo battery packs for e-bikes are hard to find, especially one with high output if you are building a racing bike for riding off road.

You’ll notice that for my charge wires I used larger diameter wires than the sense wires that came with the BMS. That’s because charging will deliver more current than those sense wires will. Also, you’ll notice the discharge wires (including the B- pad to the negative terminal of the pack) are the thickest wires of all of them, as these will carry the entire power of the whole pack during discharging. I used 16 awg for the charge wires and 12 awg for the discharge wires.

Different batteries have different amperage capacities. Most cheap lithium batteries are not capable of putting out much amperage. If you have a 48 volt bike that performs well when using 25 amps, you are going to want a 48 volt battery that has close to a 20-Amp-hours or more.  If you want to eventually hot rod your ebike (read our hot rod hub motor primer here), you may want to  invest now in a high amperage battery. This will “future proof” your system by paying a little bit more now for the battery, but then you can program more performance from the controller in the future, if you want…

Leave a Reply

Your email address will not be published. Required fields are marked *