“electric bike batteries lithium _battery for scooter”

LiFePO4 is currently widely available for purchase as e-bike packs complete with BMS on ebay and other online merchants. Mostly it is sold by small companies. Also, most of the commercially available e-bikes powered by lithium batteries are using the LiFePO4 chemistry.

Author’s note: Hi guys, Micah here. I run this site and wrote this article. I just wanted to let you know real quick about my new book, “DIY Lithium Batteries: How To Build Your Own Battery Packs” which is available in both ebook and paperback format on Amazon and is available in most countries. It goes into much deeper detail than this article and has dozens of drawings and illustrations showing you every step of designing and building a battery. If you find this free site helpful, then taking a look at my book can help support the work I do here to benefit everyone. Thanks! Ok, now back to the article.

By entering the Sweepstakes you agree to receive email newsletters periodically from Electric Bike Technologies LLC. You can opt-out of receiving this communication at any time by clicking the unsubscribe link in the newsletter.

The following is an overview of the ShippingPass Pilot subscription service. You should review the Terms & Conditions for a more detailed description as well as service limitations prior to signing up for ShippingPass.

This pattern continues until we’ve got all 10 parallel groups connected. In my case, you can see that the first and last parallel groups aren’t welded on the top side of the pack. That is because they are the “ends” of the pack, or the main positive and negative terminals of the entire 36V pack.

I want to build some custom batteries, but I am hesitant to do the spot welding myself. Aren’t there modular and affordable pieces of hardware one can use to connect the batteries? Something like this?

i have the exact same BMS but i only have 6 cells, 2p x s3 , i have 2x 3.7v @ 2000 mah batteries in parallel connected to another 2 parallel batteries in series and another parallel pack in series if that makes sense to make a total of 11.1 v @ 12mah for a small project.

Hello Micah: Thanks for this most interesting and useful article! I want to build a battery in a 39mm x 520mm seatpost for fueling a 250W motor that normally uses a 7.2 Ah – 25 V bottle-shaped battery. The new seatpost battery should only have an autonomy of 7 miles of steep hills (40%) between each daily charge. What are your recommendations? Happy day! Fred

batteries e bike battery exide electric bike battery 48v battery 48v electric bike battery 24v battery gp battery 36v battery aw battery aeg battery ev battery 48v e bike battery 3c battery ima http://twowheelev.com bb battery More…

For a 24V 7s pack, I’ve used this BMS a few times and been quite happy with it: http://www.aliexpress.com/item/7S-Li-ion-Lipo-Batteries-Protection-Board-BMS-System-24V-29-4V-20A-Continuous-Discharge-350W/32336397316.html

BMS’s aren’t required, they just make life easier. As you mentioned, if you don’t use a BMS then you’ve got to diligently monitor your cells and use balance charging to manually balance your cells. A BMS just takes care of this hassle for you. A low quality BMS can cause problems, but good quality BMS’s shouldn’t risk cell damage.

Pedals: Foldable. 26\” wheels with Aluminum Alloy spokes. Opportunity: Outdoor Camping, Mountain. 36V 8AH Lithium-Ion Battery. Material: Aluminum Alloy. Wheel diameter: Approx. Head height (To ground)…

I use white 2mm thick craft foam and cut out a shape slightly larger than my pack. I wrap it up and seal it with electrical tape. It doesn’t have to be pretty, it just has to cover the pack. Your next step will hide the foam from view.

I’m planning on building a 10S12P pack for usage on a custom DPV (Diver Propulsion Vehicle). For packaging purposes, it would be best for me to split the battery pack in several battery modules instead of a single block of cells.

Something that’s worthy of note, is that “AllCell” is using a block of graphite/wax composite Phase-Change-Material (PCM) using a patented formula. If a single cell suddenly starts running hot, the heat is instantly spread out across the PCM block, which would prevent a thermal runaway event. According to a recent press-release:

I am not sure their interests align with mine. I would happily live with 1500 recharge cycles () by which time i would be sick of it anyway) instead of 2000 if I could use 3c in or out when urgently needed.

100~240VAC Universal AC input Full range LiFePO4/Lithium Ion/Lead Acid 4000W Battery Charger Two S2500 model in parallel. Power:4000Watts; Protection function: / Overload / Over voltage / Over temperature / Over current / Reverse polarity / Power off or trickle after finished charging; 2 years warranty

0 Replies to ““electric bike batteries lithium _battery for scooter””

  1. I figured this would be a critical step I wouldn’t want to mess up. Thanks for the advice on using the multimeter. That’s good to know as I thought I might need to open up the controller and see which wires went where on that male xlr connection which I guess would be an option too. Thanks again!
    22f cells are quite low capacity and not very strong. They will work for an ebike (and are about the cheapest good quality cells out there) but they aren’t optimal. You’ll end up with a larger and heavier pack as compared to more energy dense cells like Panasonic 18650pf or Sanyo 18650ga cells.
    Electric Bike Technologies LLC has the right, in its sole discretion, to maintain the integrity of the Sweepstakes, to void votes for any reason, including, but not limited to; multiple entries from the same user from different IP addresses; multiple entries from the same computer in excess of that allowed by sweepstakes rules; or the use of bots, macros or scripts or other technical means for entering. Any attempt by an entrant to deliberately damage any web site or undermine the legitimate operation of the sweepstakes may be a violation of criminal and civil laws and should such an attempt be made, Electric Bike Technologies LLC reserves the right to seek damages from any such person to the fullest extent permitted by law.
    We also maintain stock of replacement vertical seattube batteries that have been in use in the eZee bicycle line since time immemorial. If you have an eZee bike circa 2008-2012 with the Phylion lithium battery pack, you’ll be in for a serious upgrade with over twice the capacity in the same size and weight.
    Good question. The answer comes down to the difference between “nominal voltage” and “actual voltage”. LiFePO4 cells are nominally called 3.2V cells, because this is their voltage in the middle of their discharge curve, at about 50% discharge. They actually charger to a higher voltage though, about 3.7V per cell. That means that you need a charger that has an output voltage of 3.7V x 6 cells = 22.2V DC. This is going to be a bit harder to find because most LiFePO4 packs come in multiples of 4 cells, (4, 8, 12, 16 cells, etc) so finding a charger for a 6S pack might take some searching. This charger is a good quality one meant for 8 cells (output voltage of 29.2V DC) but if you put a note in the purchase order, the seller can adjust the output for 6 LiFePO4 cells (22.2V DC). http://www.aliexpress.com/store/product/aluminum-shell-24V-29-2V-3Amper-Lifepo4-battery-charger-high-quality-charger-for-8S-lifepo4-battery/1680408_32274890691.html

Leave a Reply

Your email address will not be published. Required fields are marked *