“diy electric bicycle electric bike diy”

Yea lead acid is a great way to cheaply get into ebikes and test new motor/controller combinations. Keep in mind though that your performance will increase when you switch to lithium. It’s easy to do though, as the bike doesn’t care what chemistry it receives, it just sees volts and amps. Good luck!

Next, plan out your cell configuration on your computer or even with a pencil and paper. This will help ensure you are laying out your pack correctly and show you the final dimensions of the pack. In my top-down drawing below I’ve designated the positive end of the cells in red and the negative end of the cells in white.

The controller that came with my ebike conversion kit just has the label ’48v 1000w’ on it and there are no other specifications anywhere to be seen. I have emailed the suppliers asking if I could have a full list of specifications for the controller but am yet to hear back from them.

Then I took the sense wire labeled B1 and soldered it to the positive terminal of the first parallel group (which also happens to be the same as the negative terminal of the second parallel group, as they are connected together with nickel strip).

Thanks so much for the info, that sounds great and an exciting option! I understand the warranty issue but aside from that, you don’t see any issue than with building a battery of any capacity and just making the discharge cable with an xlr connection to plug into the bike. Would I need a different cable to charge the battery or does it charge via the xlr connection like theirs? Here is one more link with a few more answered questions about their auxiliary battery if you wanted more info. Thanks again, this is really exciting, I just want to make sure I don’t fry anything

I assume you mean 52V (14s, or 14 cells in series) which is a somewhat common lithium ion battery configuration. It works with most 48V setups but provides a little more power than a standard 48V (13s or 13 cell) battery. A good charger I recommend for 52V 14s batteries is this one.

Spot welders for batteries aren’t the same as most home spot welders. Unlike the large jaw spot welders for home workshops, battery spot welders have the electrodes on the same side. I’ve never seen them for sale in the US, but they can be found pretty easily on eBay and other international commerce websites. My full time use welder is a fairly simple model that I got here. A highly recommended source for a slightly nicer spot welder design (pictured below) with both mounted and handheld electrodes can be found here.

I want to build a 36v ebike battery for my 36v 500w motor. What battery you recommend for me which gives the enough current and capacity. My plane is to build a battery with 40 cells 10 in s and 4 in p,

26′ rear wheel 48v 1000w hub motor (powerful Motor with hall sensor ) Electric Bike Kit With or Without Battery. 26′ size REAR WHEEL 48V 1000W ELECTRIC BIKE KIT WITH or WITHOUT BATTERY. 48v 1000w brus…

36V 10ah Lithium battery (Included with the battery is the charger and mounting Bracket). Standard 26 in by 4in Front Wheel 500w brushless motor hub ( disc brakes). Pedal Assistance system included ( …

When it comes to the nickel strip you’ll be using to connect the 18650 batteries together, you will have two options: nickel-plated steel strips and pure nickel strips. Go for the pure nickel. It costs a little bit more than nickel plated steel but it has much lower resistance. That will translate into less wasted heat, more range from your battery, and a longer useful battery lifetime due to less heat damage to the cells.

When I’m experimenting with some new ebike parts and want to test different battery voltages for different speeds, I often use lead acid batteries because I can try many different voltages using very cheap batteries. Then when the results of my lead acid battery tests show me whether I want to go with 36V or 48V or 60V, for example, I then commit to buying the appropriate lithium battery.

My question for you is, if I just want to run a BMS for balance charge purposes only and want to wire the battery discharge directly to the motor how would I do that? Would that be a good solution as long as I monitor battery pack voltage during rides?

I have been looking up materials and researching where to buy them for my battery pack. I’ve come to the exact conclusions (and almost the exact same materials) that you write about in this great article. Too bad i didn’t find it earlier… Doh!

If those are new cells then I’m surprised that the voltages aren’t identical. That difference (0.08V) is about the farthest difference I’d want to see between cells. Ideally you should charge that 3.82V cell up a bit more before you connect it in parallel with the others. I’d run tests on all of those cells though with a capacity tester to ensure they are good quality cells though. Genuine cells straight from the factory should all have identical voltages.

That is definitely possible, but keep in mind that the 10 modules you want to connect in series will only need one wire between them. You don’t need to connect the negative and positive of each to the next – you only need a wire from the positive of module 1 to the negative of module 2, then a wire from the positive of module 2 to the negative of module 3 and so on.

Believe it or not, most BMS’s can handle the current from regenerative braking in the discharge mosfets as its rarely more than 5-7A. Some BMS’s (called two wire BMS’s) actually use the same mosfets for charging and discharging. Those inherently should be more than capable of dealing with the load from regen.

Most of the problems occur when charging an ebike because they are unsupervised and that is when a LiPo fire can burn down a house etc. Use common sense on where you are going to charge your bike or battery pack, so that if it does burst into flames it does not take your house with you. I have a big steel barbecue grill set up in my entryway which  I charge my battery packs in  as nice safeguard.  This involved taking the battery pack out of the bike after each ride but I am OK with that:

However, when you factor in the shorter life cycle of lead acid batteries, they become comparable to lithium batteries over the entire life of the electric bicycle. For example, a lithium battery may cost five times the price of a lead acid battery, but it could easily last five times as long as well, making the price about the same over the life of the lithium battery. You’d have to buy at least four replacement lead acid batteries (maybe even more) by the time your lithium battery finally kicks the can.

4. How to Enter: The Sweepstakes must be entered by submitting an entry using the online form provided on this site. The entry must fulfill all sweepstakes requirements, as specified, to be eligible to win a prize. Entries that are not complete or do not adhere to the rules or specifications may be disqualified at the sole discretion of Electric Bike Technologies LLC. You may enter only once and you must fill in the information requested. You may not enter more times than indicated by using multiple e-mail addresses, identities or devices in an attempt to circumvent the rules. If you use fraudulent methods or otherwise attempt to circumvent the rules your submission may be removed from eligibility at the sole discretion of Electric Bike Technologies LLC.

Now the game plan here is to weld batteries for motor scooters groups of 3 cells (or more or less for your pack depending on how much total capacity you want). To weld the cells in parallel, we’ll need to weld the tops and the bottoms of the cells together so all 3 cells share common positive and negative terminals.

HERE ARE 99 GENIUNE LG LGABB41865 18650 2600MAH CELLS. THEY ARE IN MODEM BATTERIES, JUST NEED A FLAT SCREW DRIVER AND PRY THE CASE AT THE SEAM. THEY ARE IN 12V (3S1P) SET UP ALREADY SO YOU CAN SAVE A …

Leave a Reply

Your email address will not be published. Required fields are marked *