“battery for scooter -bike battery power”

Cool project! I’d check out electric rider (www.electricrider.com) as I know they have some good electric rickshaw and electric tricycle kits. You’re looking for a strong 48V motor that is geared really low. You want torque, not speed. With slow speed, something in the 1,000 – 1,500W is probably enough. Just don’t expect to be flying down the road…

RC packs may be fine for enthusiasts that know what they’re doing, but even telling others about them scares me! FIRE! And secondly, they typically don’t have any BMS so don’t have any inherent protection from over-under voltage or balancing. FIRE!

Lithium Polymer is by far the lightest battery option out there. LiPoly cells that can handle very high discharge currents are becoming widely available and are especially popular in the R/C crowd for electric airplanes and helicopters, but ebike LiPoly packs are often made with cells that are only rated to 1C or 2C, and these don’t usually deliver a very good cycle life count. The cells are produced in a thin plastic pouch rather than a metal can, making them structurally quite vulnerable unless supplied with a rigid enclosure. Although Lithium Polymer has a reputation for being volatile and failing with spectacular pyrotechnics, there are companies making cells these days that are quite stable and can pass the fullUN 38.3 overcharging and puncture tests without any flames.

Yes, I’ve seen this problem. Homes that have only a 10A circuit breaker are often not enough for these welders. The room I wanted to use mine in had a 10A, so I switched it for a 20A breaker at the breaker box and now it works fine.

The spacers you linked to make battery building a bit easier as you can set it up modularly, but as you indicated, they add a good amount of volume to the battery. I like to make my batteries as small as possible so I rarely use them. When I do, I use these ones, but it’s not very often.

HERE ARE 99 GENIUNE LG LGABB41865 18650 2600MAH CELLS. THEY ARE IN MODEM BATTERIES, JUST NEED A FLAT SCREW DRIVER AND PRY THE CASE AT THE SEAM. THEY ARE IN 12V (3S1P) SET UP ALREADY SO YOU CAN SAVE A …

Author’s note: Hi guys, Micah here. I run this site and wrote this article. I just wanted to let you know real quick about my new book, “DIY Lithium Batteries: How To Build Your Own Battery Packs” which is available in both ebook and paperback format on Amazon and is available in most countries. It goes into much deeper detail than this article and has dozens of drawings and illustrations showing you every step of designing and building a battery. If you find this free site helpful, then taking a look at my book can help support the work I do here to benefit everyone. Thanks! Ok, now back to the article.

I’ve been reading a bit about how Batterybro.com makes sure to test there batteries are genuine, and how it seems they still get a lot of fake batteries from China. When you buy on Aliexpress.com how to you know and make sure the batteries you buy are genuine? there’s a lot of sellers how did you find yours?

One of the easiest ways to increase the current handling capability and range is to put two or more batteries in parallel. In general, with lithium batteries of the same nominal voltage, this is no problem. It is perfectly fine to mix old and new lithium batteries in parallel, or even batteries from different manufacturers and with different capacities, so long as they are the same voltage. We stock a parallel battery joining cable to facilitate connecting packs this way. 

There is some research into 18650 packs that use pressure connectors like in a remote control but most results aren’t impressive yet. It’s difficult to get a good enough connection to deliver high enough power for ebike applications. The ones that are close to working use custom designed enclosures. Don’t attempt to do it with off-the-shelf 18650 holders with spring contacts — you’ll melt them in no time.

Addresses in the following State Codes AK, HI, AE, AP, AA, PR, GU, MP, PW, AS, VI, FM and APO/FPO addresses with U.S. ZIP Codes will ship for free with value shipping. You will see this noted in checkout.

12. Privacy Policy: Information submitted with an entry is subject to the Privacy Policy stated on the Electric Bike Technologies LLC Web Site. Read the Privacy Policy here: https://www.ebikekit.com/pages/privacy-policy.

My series connections are between each group of 3 parallel cells. So all the connections that go across the short side of the pack are parallel connections, and all the connections that run along the long end of the pack are series. It doesn’t always happen that way, but the shape of this pack forced that geometry.

I was wondering, though, if I could use thick gauge wire instead of nickel strips (copper wires are much more accessible). Would there be any downsides to that, given that I’m going to be using solder anyway?

11. Disputes: THIS SWEEPSTAKES IS GOVERNED BY THE LAWS OF United States AND PA, WITHOUT RESPECT TO CONFLICT OF LAW DOCTRINES. As a condition of participating in this Sweepstakes, participant agrees that any and all disputes which cannot be resolved between the parties, batteries for electric bikes causes of action arising out of or connected with this Sweepstakes, shall be resolved individually, without resort to any form of class action, exclusively before a court located in PA having jurisdiction. Further, in any such dispute, under no circumstances will participant be permitted to obtain awards for, and hereby waives all rights to claim punitive, incidental, or consequential damages, including reasonable attorneys’ fees, other than participant’s actual out-of-pocket expenses (i.e. costs associated with entering this Sweepstakes), and participant further waives all rights to have damages multiplied or increased.

You can buy LiFePO4 straight from China from Ping Battery. These batteries are a little bulky, but are safe, and will last over 1000 charges. You can also buy ready made Lithium Iron Phoshate (LiFePO4) or Lithium Polymer (LiPo) packs from BMS battery.

The 48V, 8AH lithium battery of this ebike is removable. Material: Aluminium alloy frame. E-bike & Assisted bicycle, you can choose the E-bike to enjoy a long time travel, and also exercise. Combining…

Next, grab another 3 cells (or however many you are putting in your parallel groups) and perform the same operation to make another parallel group just like the first one. Then keep going. I’m making eight more parallel groups for a total of 10 parallel groups.

A big downside of lithium batteries is that they are much more expensive than lead acid batteries. Prices vary depending on the voltage and capacity of the lithium battery, but standard ebikes usually have lithium batteries starting in the $300 range and rising quickly from there. Most bikes I build have lithium batteries in the $400-$500 range.

To answer your question, you can definitely build your own auxiliary battery. It looks like they used a fancy right angled female XLR connector, but I imagine a standard female XLR connector will fit just as well. I’m not sure if you’ll be voiding your warranty though by connecting your own battery. Those XLR connectors can be purchased all over ebay and probably even at your local electronics shop.

Bigger is better! And I know a better way batteries should be made. I use 560 of the Panasonic 18650b battery cells with 3.4AH per cell, wich in the end gave me (7kwh battery ebike!), that’s more than 300+ miles battery range easy. And I’ve learned that these batteries can be assembled like Lego blocks instead and eliminate harmful heat from soldiering, and wastful glueing. The benefit is a battery pack that can have removable, repairable, and reconfigurable battery cells! Its called (battery blocs) patiented by Shawn McCarthy. Unfortunatly its not the cheap method and requires a 3d printer to make. It spaces the cells slightly apart for better air cooling. Mine are packed into 4 PVC tubes run either at 103.6v or 51.8v. I believe along with some experts that a BMS is not required and can cause battery cells to fail early!, and a proper set voltage monitor and regulator prevents over discharge damage and you need to a timer and monitor the cell voltages with cell monitors while charging. Cooling setup would be a pluse to extend life. That’s all for now, best luck to all battery builders.

One question regarding the specific battery BMS you used in this build: It uses a different wire for charging vs discharging the battery. Does this mean that the regenerative braking feature cannot be used for this battery?

Thanks again for the great info, that is really helpful. I just have one last question. On the XLR connections there is a hot, neutral and ground. It appears on the battery you linked to that there are just two wires, how can I ensure which prongs of the male XLR connection on the Porteur are hot and negative? Also, do I just leave the ground spot on the female XLR connection open since there is just a hot and negative wire?

The article was extremely informative, thank you. I’ve found everything but am struggling with good cells. At Aliexpress there are many choices but I’m struggling to get near the $2/cell mark you mentioned as a limit for decent cells and still find performance criteria of a good battery (or at all). So far I’ve found NCR18650B but it appears to have a 2C discharge rating for a 3400mA cell. At 4P this is more than enough but seems low for LiIon so I wonder if it is good? The price is $163 shipped to USA for 10s 4p 40 pieces to make 36v 13.6Ah. After adding shrink wrap, BMS and nickle strips I’m at $213 before buying a spot welder ($200). I can buy on the same site a 36v 15Ah Li Ion pack for $248. https://www.aliexpress.com/item/US-EU-No-Tax-DIY-lithium-18650-battery-pack-15AH-36V-Electric-Bike-battery-for-36V/32757165516.html?spm=2114.13010208.99999999.274.JmcpBS

Spot welders for batteries aren’t the same as most home spot welders. Unlike the large jaw spot welders for home workshops, battery spot welders have the electrodes on the same side. I’ve never seen them for sale in the US, but they can be found pretty easily on eBay and other international commerce websites. My full time use welder is a fairly simple model that I got here. A highly recommended source for a slightly nicer spot welder design (pictured below) with both mounted and handheld electrodes can be found here.

While it is possible to build packs with any number of cells for just about any voltage, most have standardized in 12V increments, with 24V, 36V, and 48V being most common, and 72V used on occasion. Battery chargers are usually only stocked for these voltages as well.

All the help and knowledge I’ve provided here on EbikeSchool.com is 100% free, and I try to assist readers as much as possible in the comments section of each article. If you want to support this site and help me keep it free (and ad free), consider checking out my ebook and video course on building ebikes.

A 48 volt 20-Ah pack  contains 960 watt hours and once you get close to 1000 watt hours you are getting serious commuting range which most e-bike manufacturers promise but do not deliver…think 30 miles.

I am not sure their interests align with mine. I would happily live with 1500 recharge cycles () by which time i would be sick of it anyway) instead of 2000 if I could use 3c in or out when urgently needed.

This is our smallest battery offering specifically aimed at people who have to travel or fly with their ebike. Each module is 36V 2.7Ah, so just under 100 watt-hours, exempting it from most of the heavy shipping restrictions. You can parallel connect them for as much capacity as required, and series connect them for 72V setups. Designed and made in Canada by Grin Tech, full details here.

For people who are new to the hobby, ready-made lithium packs are the way to go. Several manufacturers offer ready to go Lithium packs with a built in Battery Management System (BMS) at affordable prices.

Work in a clean area free of clutter. When you have exposed contacts of many battery cells all wired together, the last thing you want is to accidentally lay the battery down on a screwdriver or other metallic object. I once nearly spilled a box of paperclips on the top of an exposed battery pack while trying to move it out of the way. I can only imagine the fireworks show that would have caused.

I have built a few 13s lithium batteries in the past year following your instructions. Thanks. I have taken one of the batteries apart to check its condition as it is the middle of winter here in Winnipeg, Canada. Two parallel sets were out of balance with the rest of the pack. I was wondering if there is a way to use my imax b6 balance chargers to rewire the battery and keep each parallel pack in balance for sure! This way I will bypass the bms. Does this make sense?

One Reply to ““battery for scooter -bike battery power””

  1. Here at Grin we’ve been dealing with ebike batteries for a very long time during which we’ve offered over 100 variants of NiCad, NiMH, LiFePO4, LiPo, and Lithium-Ion packs in all kinds of voltages, geometries, and capacities. It’s been a love/hate relationship over those years, but the more recent mass production of 18650 lithium cells for high power consumer goods like power tools has shifted things to the love side, with ebike batteries that are cheaper, lighter, and with far longer life span than we could have ever wished for in the past. We’re happy to stock both frame mount and rear rack mounted batteries from 98 watt-hours to 1100 watt-hours in size to suite the needs of most electric bicycle conversions. 
    The eZee flat packs are one of the nicer rear rack battery options that we’ve dealt with, featuring a locking on/off key switch, and a rail system to slide into the eZee double-decker rack or attach with our more universal CNC battery anchors. They hold up to 70 cells, allowing for both a 36V 19Ah (10s 7p) and 48V 14Ah (13s 5p) options. The 36V pack has UN38.3 certification for air shipping, and can handle up to 40A motor controllers fine, while the 48V pack shouldn’t be used above 25A.

Leave a Reply

Your email address will not be published. Required fields are marked *