“battery for a scooter scooter batteries 36v”

3. Lastly, I assume if the BMS & battery were able to produce the 50A X 24V watts of 1200W that my electric motor would only ever use the 500W it is rated for? As in the E bikes controller would only draw around 500W?

5. Prizes: The approximate retail value of all prizes is $1361. The prizes are: Performance E-BikeKit or Heavy Duty E-BikeKit. You are not guaranteed to win a prize and your chance of winning is dependent on the total number of eligible entries received. Actual/appraised value may differ at time of prize award. The specifics of the prize shall be solely determined by the Sponsor. No cash or other prize substitution permitted except at Sponsor’s discretion. The prize is nontransferable. Any and all prize related expenses, including without limitation any and all federal, state, and local taxes shall be the sole responsibility of the winner. No substitution of prize or transfer/assignment of prize to others or request for the cash equivalent by winners is permitted. Acceptance of prize constitutes permission for Electric Bike Technologies LLC to use winner’s name, likeness, and entry for purposes of advertising and trade without further compensation, unless prohibited by law.

Features: It is so light weight , easy to transport and to take it. It is eco-friendly and safe to use it. The battery holder is so stable and sturdy. Super powerful,safe and reliable. Suitable for bi…

Typically you can expect somewhere between 25 and 70 miles of travel on a single charge of an ebike. If you’re riding hard on full power expect less; manage your battery life well and you could get more.

The battery cells have now been assembled into a larger 36V pack, but I still have to add a BMS to control the charging and discharging of the pack. The BMS monitors all of the parallel groups in the pack to safely cut off power at the end of charging, balance all the cells identically and keep the pack from being over-discharged.

I hope not to have to replace the whole battery pack and wondering if it can be salvaged by replacing the just the dead cells and burnt connectors, or do you think the damage is too extensive to be worth repairing it?

The controller that came with my ebike conversion kit just has the label ’48v 1000w’ on it and there are no other specifications anywhere to be seen. I have emailed the suppliers asking if I could have http://electricbikebatterys.com full list of specifications for the controller but am yet to hear back from them.

I would prefer to go with lithium, but I have a couple of 75 volt (i think) cells from a UPS that are brand new. They are built from regular 12v (sixteen total) sealed lead units and would make the initial investment in an ebike that much more reasonable. One huge downside is that I hope to use the folding ebike in my homebuilt aircraft. As with ebikes, excess weight is to be avoided!

Good question. The answer comes down to the difference between “nominal voltage” and “actual voltage”. LiFePO4 cells are nominally called 3.2V cells, because this is their voltage in the middle of their discharge curve, at about 50% discharge. They actually charger to a higher voltage though, about 3.7V per cell. That means that you need a charger that has an output voltage of 3.7V x 6 cells = 22.2V DC. This is going to be a bit harder to find because most LiFePO4 packs come in multiples of 4 cells, (4, 8, 12, 16 cells, etc) so finding a charger for a 6S pack might take some searching. This charger is a good quality one meant for 8 cells (output voltage of 29.2V DC) but if you put a note in the purchase order, the seller can adjust the output for 6 LiFePO4 cells (22.2V DC). http://www.aliexpress.com/store/product/aluminum-shell-24V-29-2V-3Amper-Lifepo4-battery-charger-high-quality-charger-for-8S-lifepo4-battery/1680408_32274890691.html

I am planning to build a 14s7p pack with the GA batteries for a little over 1 KW of power. I went to the BesTechPower site and their are several 14s BMS’s there. Which one would you recommend for a battery this size? Can you send/post a link to the specific on on their site? thank you.

9S, 32.85VDC, 2890MAH, 94.93WH. THE ENERGY DENSITY OF THESE CELLS ARE SPECTACULAR. YOU GET A POSITIVE AND NEGATIVE LEAD WIRE AND ALSO BALANCE CONNECTORS IF YOU WANT TO BALANCE THE CELLS. IF YOU BUILD …

Hi Micah,I am from INDIA want to construct a 36v,15 ah,peak current 15 amp,continuous current 6 to 8 amps. Now ipurchased 20 pcs new IFR 18650 lifepo4 rechargeable cells,and a BMS36v,lifepo4 BMS12s forE.Bike lithium battery pack 12s,36,v,PCm.How many cells total i have to use for my aim?What kind of charger (specification) i have to purchase? Your article and reply to questions are interesting.please guide me.

Alibaba.com offers 176,519 electric bike battery products. About 29% of these are electric bicycle, 22% are rechargeable batteries, and 8% are electric bicycle battery. A wide variety of electric bike battery options are available to you, such as 36v, 24v, and 48v. You can also choose from lithium battery, lead acid battery. As well as from 10 – 20ah, 21 – 30ah, and > 40ah. And whether electric bike battery is paid samples, or free samples. There are 176,478 electric bike battery suppliers, mainly located in Asia. The top supplying countries are China (Mainland), Taiwan, and Vietnam, which supply 99%, 1%, and 1% of electric bike battery respectively. Electric bike battery products are most popular in North America, Western Europe, and Northern Europe. You can ensure product safety by selecting from certified suppliers, including 39,164 with ISO9001, 14,565 with Other, and 6,300 with ISO/TS16949 certification.

i noticed that bms installation is different (as i guess) from the video (https://www.youtube.com/watch?v=rSv9bke52eY&index=10&list=LLDXj2cy8mbQoc0dz3RO3zFw) i have watched before. In this video bms wires were connected on the negative poles of batteries lifepo4. In my amateur opinion i could not understand how we organize BMS connections for my 13s pack. if you illuminate me, i will be preciated.

One Reply to ““battery for a scooter scooter batteries 36v””

  1. Believe it or not, most BMS’s can handle the current from regenerative braking in the discharge mosfets as its rarely more than 5-7A. Some BMS’s (called two wire BMS’s) actually use the same mosfets for charging and discharging. Those inherently should be more than capable of dealing with the load from regen.

Leave a Reply

Your email address will not be published. Required fields are marked *